Lab Report Accurate Measurement of Mass and Volume

Laboratory Report 1 Title : Accurate Measurement of Mass and Volume Part A: The Formula of Hydrated Copper (II) Sulfate Aim: The objective of this experiment is to find out the accurate mass of a solid and to calculate the moles of an unknown. Materials: The materials used in this experiment are Hydrated Copper (II) Sulfate, weighing bottle, analytical balance, laboratory balance, casserole, spatula, and hotplate. Methods: First, approximate 1.0g of hydrated copper (II) sulfate was transferred into a weighing bottle and the lid was screwed on. The colour of the solid was noted.The capped bottle was then taken into the analytical room and its mass was accurately measured. Then, the copper (II) sulfate was transferred from†¦show more content†¦Materials: The materials used in this experiment are Potassium Permanganate, beaker, pipette, pipette filler, dropper, 100cm3 volumetric flask, water, cuvette cell and ultraviolet-visible spectrophotometer. Methods: First, no more than 20cm3 of the coloured solution (PotassiumShow MoreRelatedLaboratory Techniques and Measurements Essay968 Words   |  4 PagesLaboratory Techniques and Measurements Peter Jeschofnig, Ph.D. Version 42-0165-00-01 Lab RepoRt assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions, diagrams if needed, and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing of lab reports by providing thisRead MoreMass Density Of An Unknown Metal Essay1066 Words   |  5 Pages The goal of this experiment was to determine the mass density of an unknown metal. Five different vernier capillaries and double pan balances were used to measure the metal. The plan of action was to find the average density to reduce random error, in addition to, calculating the standard error to observe the reliability of proposed average. Ideally, the metal would identify more comparably with gold or aluminum. The concepts of mass density, standard error, average, one-dimensional statisticsRead MoreChemistry Experiment Essay1131 Words   |  5 PagesLab Report Experiment 1 amp; 2 CHM-101 Amele Takpara Partner: Jessamyn Dupree ------------------------------------------------- Experiment 1 ------------------------------------------------- (Pre-Lab Questions) 1. In the design of a Bunsen burner, explain the purpose of a. the gas control valve The gas control valve regulates the rate at which methane enters the burner. b. and the air vents. The air vents control the rate at which air enters the burner 2. Why is a luminousRead MoreDensity of Sprite1742 Words   |  7 PagesGeneral Chemistry I Lab 09/12/2007 Lab 7 Density of Sprite and Diet Sprite Abstract: The density of regular Sprite was found to be 1.037 +/- g/mL. compared to Diet Sprite which was 0.9965 +/- g/mL. Among the three volumetric glassware Pipette was most precise (à ³=0.0016 g/mL). Burette was the second best (à ³=0.0023 g/mL) and graduated cylinder was the least precise (à ³= 0.007 g/mL). Density was found to be intensive property. The slope of the graph of mass against volume was 1.05 g/mL, with theRead MoreDetermination of the identity of an unknown liquid Essay1644 Words   |  7 PagesChemistry Lab Report Purpose The purpose of this lab is to determine the identity of an unknown liquid by measuring its density and its boiling point and try to match it with those solutions given in Table 2 of experiment 2. Procedure Part A In Part A, The main purpose was to find the determination of the density of the unknown (j41) and by doing that we had to determine volumes of the unknown liquid (j41) using three different volumetric devices which are graduated cylinder, pipetteRead MoreLabpaq Lab Techniques and Measurements Essay1512 Words   |  7 Pagessystem of units (SI), to become familiar with common lab equipment and techniques, to gain proficiency in determining volume, mass, length, and temperature of a variety of items using common laboratory measurement devices, to learn to combine units to determine density and concentration, and to use laboratory equipment to create serial dilutions and determine the density and concentration of each dilution. Procedure: Measure the volume, mass, length and temperature of a variety of items. CreateRead MoreEssay about Lab 1-Measurement, Length, Mass, Volume, Density Time 1380 Words   |  6 Pagesï » ¿ GS104 Lab Report Experiment # 1 Measurement, Length, Mass, Volume, Density Time David Case: January 17, 2015 Experiment #1 Measurement, Length, Mass, Volume, Density, Time Objectives: To make basic distance, mass, density, and time measurements. To make calculations of volume and density, using proper units, and to practice using graphing software while graphing the relationship between the circumference of a circle and its diameter. Read MoreChemistry Beverage Lab Report Essay1265 Words   |  6 PagesJoanna Park Mrs. Carrillo CP chemistry per. 5 September 17, 2012 i. Beverage Density Lab Report ii. Purpose: The purpose of this experiment is to determine the percentage of sugar content in beverages. iii. Materials: Distilled water, beverages (juice, soda, sport drinks), Sugar reference solutions (0, 5, 15, ad 20%) 25ml each, Balance, centigram(0.01g precision), Beaker (100-mL), Erlenmeyer flask (125-mL to collect rinse solutions), Pipet(10-mL), Pipet bulb or pipet filler ivRead MoreLabratory Techniques and Measurments1186 Words   |  5 Pages Date of Experiment: February 5, 2013 Report Submitted: February 11, 2013 Title: Laboratory Techniques and Measurements Purpose: To gain knowledge about the International System of Units and use it to determine volume, mass, length, and temperature. To learn to use these forms of measurement to determine density and concentration, as well as learning basic lab equipment to create dilutions. Procedure: Part 1: After reading the various informationRead MoreLaboratory Techniques and Measurements Essay824 Words   |  4 PagesLaboratory Techniques and Measurements Choose any three objects that are shorter than the metric ruler to measure, such as a CD, Key, spoon etc. OBJECT | LENGTH (cm) | LENGHTH (mm) | ruler | 30.5 cm | 305 mm | thermometer | 15.1 cm | 151 mm | pencil | 16.7 cm | 167 mm | Warm Temperature Measurements * Fill a 100 a 100mL beaker with 50mL of hot water. Get the water as hot as possible. * Use thermometer to measure the temperature of the water in the beaker using Celsius unit